Thank you! Your submission has been received!
Oops! Something went wrong while submitting the form.
Queen Creek has a lot of new houses with big, empty garages, and the slab in them is greener than most people expect. Coating one properly starts with knowing how new that concrete really is.
Call (602) 820-7739A new slab is not automatically a good slab to coat.
Three car garages are standard on the newer streets, and they fill up with a workbench, a golf cart, sports gear and a second refrigerator alongside the vehicles. The floor arrived with the house unfinished, and it is the only surface on the property left as raw material.
Fresh concrete carries water for months after the pour and keeps pushing it toward the surface as it cures. Coat over that too early and vapor collects underneath, which is what makes a floor bubble or peel away in sheets a year later. The same rules apply to coating green concrete anywhere on a property, not only in a garage.
Timing and preparation are what prevent it. Dialed In Epoxy tests the slab, grinds it to an open profile, and specifies a build that suits how much moisture is still moving through the concrete.
We coat new build garages, extended bays and detached shops across Queen Creek, from a single car footprint up to a garage deep enough for an RV.
Cannot believe what an amazing job Kevin and his crew did! Throughout the whole process Kevin kept me informed the whole way and went above and beyond to make sure my floor was everything I wanted and asked for.
Metallic is the finish for a garage that gets looked at as much as parked in.
The pigment sits in a clear resin and is moved before it sets, so it separates into layers of color with real depth. Most people read the result as stone, though it can be pushed toward something closer to liquid metal.
Because it develops during the cure, the floor cannot be duplicated and neither can a sample exactly. It takes color direction well, so it can be built around an interior scheme rather than picked off a chart.
Flake is what most new build garages here get finished with.
It is a layered build: flake broadcast into the wet base, scraped back level, then sealed twice with polyaspartic that stays color stable in direct sun.
The texture underfoot gives grip when the floor is wet, and the flake pattern hides the dust that blows off open lots and nearby construction. It resists the usual garage chemicals and takes a loaded golf cart or a workbench without marking.
Cleaning is a dust mop and a wet mop with mild detergent, with no stripping or resealing cycle. The coating can carry through to a patio or a side entry when the outdoor space is being finished at the same time. For the yard itself, the pad and the drive, see concrete coatings for Queen Creek pads and aprons.
The cured resin is hard and thick, so vehicle weight, dropped tools and equipment being moved around do not chip it. It resists moisture, dust and grit, plus the hot tire pickup that lifts a builder grade paint finish within a season.
A closed slab gives dirt nowhere to sit, so a mop handles it. In Queen Creek that mostly means the fine dust that comes off undeveloped land and settles over everything in an open garage. Indoors it is the same routine for the same reasons: here is what looking after a Queen Creek resin floor involves.
The top coats are 100% UV stable, so the area inside a door left open all afternoon does not go yellow. The base coats hold back the moisture that new concrete keeps releasing, which is the point of failure on a young slab.
Concrete is porous, and a garage slab is the least protected concrete in the house. A resin layer over the top takes the abrasion, the spills and the impact, which leaves the structural slab doing the job it was poured for.
Every Queen Creek garage runs through the same six stage process, whichever finish goes on top. On a newer slab the moisture testing at the start is what decides the build, so it never gets skipped to save a day.
We start by mechanically grinding, profiling, and vacuuming the concrete garage floor to ensure the strongest adhesion possible.
No matter the damage, we repair every crack and hole in the garage floor.
We apply a base coat for flake flooring and 100% solids epoxy or primer coat for metallic epoxy.
For flake flooring, we broadcast the polymer flakes to provide even color and texture. For the metallic floor, we apply the metallic color coat. For 100% solids epoxy, we apply the second coat.
For flakes, we scrape off all excess bits to prepare the floor for the final step.
We finish with two coats of UV stable polyaspartic topcoat.
Three questions come up on nearly every new build garage we quote in Queen Creek.
If you want to protect your concrete floor from damage, improve safety, and keep your space looking its best, give us a call or fill in our FREE quote form.
Phoenix, Peoria, Scottsdale, Mesa, Gilbert, Tempe, Glendale, Chandler, Queen Creek, Ahwatukee, San Tan Valley, Maricopa, Avondale, Paradise Valley, Tolleson, Wickenburg, Gold Canyon, Goodyear, New River, Prescott, Fountain Hills, Desert Ridge, Sedona, Surprise, Litchfield Park, Cave Creek, Apache Junction, Buckeye and the rest of Arizona.
